About / Description

National Lab. for Soil Investigation & Building Materials Testing is a professional licensed leading soil and building materials testing laboratory in Northern Emirates established on 19 September 1987 at Sharjah, UAE, under the ownership of Eng. Khalid Abdullah Ali Suhail, and Eng. Abdullah Amiri, under Sharjah Laboratories Registration Program, a certified management system that conforms with ISO 9001:2015 and Ministry of Energy & Infrastructure.

National Lab. for Soil Investigation and Building Materials Testing main office is located at Industrial Area 3, beside Sharjah Municipality near Geco signal, Sharjah, with branch at Ras Al Khaimah, (Dahan Area) behind Shk Mohd Bin Salim Al Qasmi Road.

GEO-TECHNICAL INVESTIGATION (SOIL INVESTIGATION)

Soil investigation is to carry out physical testing on site to understand the ground conditions for geotechnical design for foundations, retaining walls and soil improvement. It allows the engineer to workout safe and economical design of a project and inform the construction engineer about the material and conditions he will
encounter in the field.

Its objective is to determine engineering properties of soil, to select a suitable type of foundation, to estimate the probable and maximum differential settlements and mainly to find the bearing capacity of the soil, which could be used in the engineering design and specifications of the proposed construction projects like building,
infrastructures, villas, etc.

The site works involves auger boring including sampling and Standard Penetration Test (SPT), trial pits, ground water level measurement, and followed by laboratory analysis for particle size distribution and chemical analysis.

CONSTRUCTION MATERIALS TESTING (CHEMICAL ANALYSIS)

The common chemical analysis for Soil, Water, Aggregates and Concrete, for construction materials, are their chloride content and sulphate content which their anions are considered as secondary contaminants. The determination of chloride and sulphate is important since these anions can have a corrosive impact on concrete structures.

There are two methods in determining the chloride and sulphate content, one is by water-soluble chloride content and water-soluble sulphate content, and the other is by acid-soluble chloride content and acid-soluble sulphate content.

SOIL TEST

The first step in construction planning is the Soil Test. It is to understand the suitability for the proposed construction work. Soil should be well tested to give excellent performance for it is responsible in allowing the stresses coming from the structure. If not tested properly, any structure could be damaged.

To decide the quality of soil for building constructions, various tests on soil are performed. The moisture content or water content of soil is an important parameter which could be determined by oven drying method, while specific gravity could be determined by pycnometer method. Atterberg limits is to measure to the critical
water content of fine grained soil. In case of shrinkage limit, the water content in the soil is just sufficient to fill the voids of soil. The Proctor test is conducted to determine compaction characteristics of soil. The degree of compaction is measured in terms of dry density of soil.

STEEL TEST

The Tensile Test is the commonly conducted test for Steel Bar. Rebar, also known as reinforcement steel and
reinforcing steel, is a steel bar used in reinforced concrete, as one of the main parts in reinforced cement concrete
structure.

The testing of Bend and Rebend are done to evaluate the ductility of the reinforced bar. The bend is performed by
bending the steel bar at the midpoint resulting in bending without fracture, while the Rebend test is performed to
measure the effect of strain ageing on steel. And Tensile test is a destructive process that provide information about tensile strength, yield strength and elongation which the steel bar involves applying increasing load up to the point of failure in both upper and lower crossheads.

ROCKS AND AGGREGATES TEST

Aggregates are inert granular materials like sand, gravel and crushed stones. The material used for mixing with cement to form a concrete which gives volume, stability, resistance to erosion and other desired physical properties to the finished product, and are tested for strength, hardness, shape, and water absorption.

The various testing of aggregates includes the impact value which gives a relative measure of the resistance to sudden impact, while crushing value gives a relative measure of the resistance to crushing
under applied load. The specific gravity and water absorption is to determine the density of the essentially solid portion of the aggregate. The LOS Angeles machine is used for testing aggregates
for resistance and degradation. The Flakiness index of an aggregate sample is found by separating the flaky particles. The Sieve Analysis helps in determining the size of a granular material like aggregates
and also all are required to meet a minimum strength valve, as defined by the 10% value test.

NATIONAL LABORATORY: frequently asked questions

Where is NATIONAL LABORATORY located?

NATIONAL LABORATORY is located in Ajman, UAE.

How can I contact NATIONAL LABORATORY?

You can contact NATIONAL LABORATORY by phone on +971 6 543 6455, by email at natinlab@eim.ae and through its website. You can also send NATIONAL LABORATORY an enquiry with the contact form on this page and the reply comes straight to your email.

Are there other Soil Investigation Services companies in Ajman?

Yes. UAECSD lists 2 other Soil Investigation Services companies in Ajman. Compare them here.


Soil Investigation Services in other emirates: